How got get valid CCNA (V3.0) 200-125 practice questions quickly?

CCNA V3.0 200-125 exam candidates may need to search 200-125 practice questions material when they should complete the exam in the discharge rate. 200-125 exam tests a candidate’s knowledge and skills related to network fundamentals, LAN switching technologies, IPv4 and IPv6 routing technologies, WAN technologies, infrastructure services, infrastructure security, and infrastructure management.

Free to get valid version 200-125 practice questions and test by yourself also. You could share your suggests or comments in our comment blank. Any suggestions will be appreciated.

Questions 1 : Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
A. Switch(config)#vlan 20
Switch(config)#Interface gig x/y
Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y
Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20
Answer: A

Questions 2 : Which three commands can you use to set a router boot image? (Choose three.)
A. Router(config)# boot system flash c4500-p-mz.121-20.bin
B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
The safer , easier way to help you pass any IT exams.
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash: c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin
Answer: ABC

Questions 3 : Which technology supports the stateless assignment of IPv6 addresses (Choose two) ?
A. DNS
B. DHCPv6
C. DHCP
D. autoconfiguration
Answer: BD

Questions 4 : After you configure the Loopback0 interface, which command can you enter to verify the status of the
interface and determine whether fast switching is enabled?
A. Router#show ip interface loopback 0
B. Router#show run
C. Router#show interface loopback 0
D. Router#show ip interface brief
Answer: A

Questions 5 : What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Answer: AD

Questions 6 : OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office.
What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Answer: C

Questions 7 : R1 does not form an OSPF neighbor adjacency with R2.
Which option would fix the issue?
A. R1 ethernet0/1 is shutdown. Configure no shutdown command.
B. R1 ethernet0/1 configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
C. R2 ethernet0/1 and R3 ethernet0/0 are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
D. Enable OSPF for R1 ethernet0/1; configure ip ospf 1 area 0 command under ethernet0/1
Answer: B

Questions 8 : An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in the Branch3 office.
What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; the username is not configured on R3 and R6.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R6.
Answer: D

Questions 9 : Why applications that are installed on PCs inR2 LAN network 10.100.20.0/24 are unable to communicate with server1?
A.A standard ACL statement that is configured on R1 is blocking the traffic sourced from R2 LAN network.
B.A standard ACL statement that is configured on R1 is blocking the traffic sourced from Server1 network.
C.A standard ACL statement that is configured on R2 is blocking the traffic sourced from Server1 network.
D.A standard ACL statement that is configured on R2 is blocking the traffic sourced from R2 LAN network.
Answer: C

Questions 10 : Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office.
Which statement correctly identifies the problem on Router R1?
A. NAT configurations on the interfaces are incorrectly configured.
B. NAT translation statement incorrectly configured.
C. Interesting traffic for NAT ACL is incorrectly configured.
D. Only static NAT translation configured from the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.
Answer: A

Leave a Reply

*